Weha
Weha Categories
Weha
Showing 205–216 of 319 results
-
Core Bits & Non-core Bits by Weha
Weha Puma T-Segment Core Bit Side Diamonds
- The Weha Puma T-Segment has a full drilling depth of 2 ¾” when the segment is worn completely down. This gives plenty of drilling depth for all countertop applications but is short enough to offer solid control when drilling
- The Puma T-Seg Core bit has vacuum brazed diamonds on the outside core to help with the drilling process by hand. It also helps if you need to make the hole just a little bigger and clean up the hole as well.
- The 4 turbo-style diamond segments act like a typical turbo diamond blade by allowing air and water(when run wet) to get in the segment while drilling as well as channel the dust out to help cut and core faster.
- The Puma T-seg diamond core bit is a very affordable core bit that offers outstanding performance. Dollar for dollar, the Puma core bit is the best for granite, quartz, quartzite, marble, and other stone.
-
Core Bits & Non-core Bits by Weha
Weha Weramic Porcelain Ceramic Core Bit
- The Weramic porcelain and ceramic core bits work excellent on all ceramic products such as floor tile and wall tile.
- Weramic core bits have been built to core perfectly smooth, chip-free holes on all thickness materials from 6mm, 8mm,10mm, 12mm 20mm, and 30mm.
- The Weramic porcelain core bits have only a 2mm thick rim. These thin wall core bits will drill very clean and fast through the porcelain and ceramic materials.
- Weramic porcelain Ceramic Core Bit is one of the best Dekton, Lapitec, or Neolith core bits that you can drill holes with.
-
Core Bits & Non-core Bits by Weha
Weha RockPecker Core Bit
Weha RockPecker Core Bit is made specifically for drilling holes in granite, quartz, engineered stone, quartzite, marble, limestone, travertine, concrete, and other stone.
- Drill very fast
- The RockPecker diamond core bit line is made to be used wet
-
Core Bits & Non-core Bits by Weha
Weha Dry Magic Vac Brazed Core Bit ⅝-11 Thread
- Weha Vacuum Brazed Diamond Core Drill Bit drills cleanly dry with zero chippings.
- The Weha Dry Magic Vacuum Brazed Core Bits are made to run between 3,000-11,000 rpm in all types of ceramic, porcelain, marble, granite.
- The vacuum brazing is on both the inside and outside of the barrel, as well two 2½” vacuum brazing up the outside barrel for full drilling depth.
- This special Vacuum II Brazed diamond technology allows an uncomplicated, hands-free, and clean drilling on angle grinders. The Vacuum diamond coating allows fast drilling with extremely clean, chip-free holes.
- Weha Dry Magic Vacuum Brazed Core Bits allow drilling depth of 2½” (60mm) with a total length of 3½” (90mm).
- Can make 50 holes depending on the material.
-
Core Bits & Non-core Bits by Weha
Weha Dry Magic Core Bit ⅝-11 Thread
- Weha Dry Magic drills cleanly dry with zero chippings.
- The Weha Dry Magic is made to run between 3,000-11,000 rpm in all types of ceramic, porcelain, marble, granite.
- The vacuum brazing is on both the inside and outside of the barrel, as well two 2½” vacuum brazing up the outside barrel for full drilling depth.
- Virtually no chipping, minimal blowout on the bottom, fast drilling, and great life.
- This special Vacuum II Brazed diamond technology allows an uncomplicated, hands-free, and clean drilling on angle grinders. The Vacuum diamond coating allows fast drilling with extremely clean, chip-free holes.
- Weha Dry Magic Core Bit ⅝-11 Thread allows a drilling depth of 2½” (60mm) with a total length of 3½” (90mm).
-
Core Bits & Non-core Bits by Weha
Weha Dry Magic Core Bit Hex Shaft
The Dry Magic Core Bit Hex Shaft is made to drill in ceramic, porcelain, granite, marble, quartz, and all-natural and engineered stones.
- The Dry Magic Core Bit Hex Shaft can all be used wet
- The Dry Magic Core Bit Hex Shaft will leave ceramic, porcelain, granite, marble, and all stone with a clean, chip-free hole without any chips or blowouts around the hole.
- The Dry Magic Core Bit Hex Shaft will drill a hole without leaving a core. This is really important when only drilling into the material without going all the way through. This is great for setting anchors, clips, screws, etc with polyesters and epoxy glues.
-
Core Bits and Finger Bits for CNC Machines
Weha Top Racer High-Speed CNC Finger Bit
- The Weha Top Racer High-Speed Finger Bit is unbelievable on Granite, marble, and especially Engineered Stone, Quartz materials.
- The Faster you run the Top Racer, the better it performs!
- The Weha Top Racer high-speed CNC diamond finger bit is the fastest cutting CNC Finger Bit on the market! Designed for production work, the Top Racer can run up to 36″ per minute fully engaged!
- With its 8 segment design, the Top Racer Finger bit will remove material at an incredibly fast rate.
-
Granite Face Polishing Systems & Radial Arm Tools
Donkey Auto-Edge 3-Step Inline Polishing Pads
- The Weha inline polishing wheels are hook & loop backed for quick replacement without the hassle of removing the snail lock holders.
- Step 0 is not needed under normal circumstances. Only use #0 if the edge is not flat or extremely rough and needs some stock removal before step 1.
- The combination of the 3 Step and Donkey pads is producing an excellent polish on all materials with all machines.
- Steps 1, 2, 3 will be used together in sequence.
